Plain gray slab looking tired or cracked? We pour stamped concrete that looks like slate, brick or stone, in a pattern that fits your upkeep.
Our stamped concrete services in Balch Springs, TX give you a patio, walk or other flatwork, the flat slabs you walk and drive on, with the look of slate, brick or natural stone, because we texture and color the surface while the concrete is still fresh.
The biggest choice you'll make is the design, and it moves both the price and the upkeep. A single pattern in one color costs less and is easier to look after, while extra colors, borders and inlays add curb appeal at a higher price and ask for more frequent care. After that, the price comes down to how many square feet you're covering and local labor rates, and the written estimate I give you spells out what's in it.
The schedule usually turns on the permit and the weather around pour day. We check with the city on every job, and when it needs a permit, the pour waits on the inspection. I won't give you a date until I've seen your ground, because I'd rather tell you what I don't know yet than guess.
I started this business in Balch Springs in 2023. We're licensed and insured, and here's who does what once you get in touch.
I come out for every estimate myself to measure, look over the ground and the drainage, and talk through patterns with you. You get a written estimate that lists what the price covers, so you can read it line by line.
Once you say yes, we check with the city or county office, and if the job needs a permit we file it and book the inspections. The pour date gets set around the inspection, not the other way around.
I run the job with our crew from setting the forms through the pour and the cleanup. You won't be handed off to someone you haven't met.
Before anything gets poured, we settle the pattern and color with you, and I'll show you how much upkeep each pattern asks for, because a busy multicolor design looks great but takes more care later. That way pour day is about doing it right, not deciding. Then we dig out and pack the subgrade, the soil the slab sits on, set the forms and the rebar, the steel that holds the slab together, pour, color and stamp the surface, and cut control joints, shallow grooves that give the slab a planned place to crack. If the budget's tight, I'd rather you pick a simpler pattern than skimp on the base, because nobody sees the base on day one, but it decides whether that pattern stays flat once the clay starts moving.
Stamped work often sits next to other jobs. A stamped patio usually needs a way to get to it, and our concrete sidewalk building can match the pattern or set it off with a plain border, while slabs like garage floor concrete get the same careful base without the stamp.
Each step sets up the next one, so we don't skip ahead. This is the order we work in.
We mark the outline and look at where the water runs, so the finished slab sheds rain away from your house instead of toward it. A slab that falls toward the foundation is one of the most common mistakes we get called to look at.
We dig past the grass and loose dirt and pack what's underneath firm, because a base that's only raked level settles with the dirt. This is the step that decides how the slab holds up.
We pour, add the color and press the pattern while the concrete is still soft enough to take it. Color can go in as a color hardener, a powdered blend of cement, pigments and fine grit that colors the top and makes it harder, and the joints get cut on time so any crack follows a line we chose.
Curing is the wait before you use the slab, while the concrete gains its strength, and we'll tell you when it's ready for feet and furniture. Then we seal it to bring out the color and protect the surface.
Send the form or call (214) 286-6733, and we'll get back to you within one business day to set a time for your free on-site estimate, with no obligation. I'll come out, measure and walk the area with you, then write down what the price covers. It helps to have the rough size, a few design ideas, any plans for the curb and your HOA's rules handy.
(214) 286-6733Stamped concrete in the Dallas area usually costs about $8 to $28 per square foot, going by one Dallas cost guide, and that's the area's going rate, not our price. Where your job lands depends mostly on its size and how busy the design is. I'll give you your own figure in writing after I've measured.
A Balch Springs driveway or flatwork permit needs a site map of the work, plus a $5000 pavement surety bond if the curb will be broken, and an approval letter from your HOA if it requires one. Under that permit, the city inspects the steel and forms before the pour, and the address and permit stay posted on the job the whole time. You can read the city's permit requirements yourself, and when your job needs a permit we take care of the filing.
One Dallas cost guide advises resealing stamped concrete every two to three years to protect it from sun and surface wear. Plan on it as a repeat job for as long as you have the slab. A multicolor design with borders asks for more care between coats than a single pattern does.
Summer is the harder season, because heat and low humidity affect fresh concrete more as the wind picks up, and those problems generally show up in summer. We plan a summer pour around the heat and wind, usually starting early before the worst of the afternoon. Ask me how we'll handle your pour day, and I'll walk you through it.
The City of Balch Springs requires every contractor to be registered with it, and the city warns that skipping a required permit can bring fines or delays, so it's worth asking any contractor you're weighing about both. We're based in Balch Springs and work across the cities around it, including Mesquite, Garland, Forney and Lancaster, and the ground and the rules are what we plan around in each one.
Most yards here sit on black clay that swells when it's wet and shrinks when it dries, and it cracks most in summer and droughts. That's why the base gets so much of my attention. One North Texas contractor's guide says topsoil, plants and other organic material have to be stripped back to undisturbed native clay, because that material rots and leaves gaps under the slab that turn into settlement cracks, and a trade group's guide calls for the subgrade to be packed and damp, with no standing water, when the concrete goes in.
We answer seven days a week from 7 AM to 11 PM, so you can call (214) 286-6733 after work with your pattern ideas in front of you.
If you've seen a pattern you like, send us a photo and we'll talk through what it takes to build and keep up.
Tell us about your project